DIN EN – Free download as PDF File .pdf), Text File .txt) or read online for free. Find the most up-to-date version of DIN EN at Engineering Buy DIN EN STEEL DIE FORGINGS – TOLERANCES ON DIMENSIONS – PART 1: DROP AND VERTICAL PRESS FORGINGS.
|Published (Last):||13 March 2013|
|PDF File Size:||3.91 Mb|
|ePub File Size:||15.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
As a general 1024-1 grade F tolerances result in a cheaper forged component. The residual flash is measured from the body of the forging to the trimmed edge of the flash, as indicated in Figure The faster, easier way to work with standards. Ost 1 71 english translation deutsch, francais, italiano Business. In those instances where the variation is of importance e.
BS EN – Steel die forgings. Tolerances on dimensions. Drop and vertical press forgings
Find Similar Items This product falls into the following categories. S3Type of steel used: Tolerances for heavier or larger forgings shall be agreed at the time of enquiry and order. They are best dealt with by consultation at the design stage and shall be agreed between the purchaser and the supplier.
Above 0,32 up to and including 0,63; S1: They are not used for check measurements on the actual forging, but for tool construction when forging dimensions are not measurable.
Many instances of heavy die wear occur in which these tolerances are inadequate. Mismatch tolerances depend on the forging mass and on the shape of die line.
In the case of a forging having a flange from which projects: The positive residual flash and negative trimmed flash values permitted are given in Table 1 and Table 2. Residual flash and trimmed flat tolerances are applied independently of, and in addition to, any other tolerances. This European Standard does not apply to upset forgings made on horizontal forging machines see EN On forged surfaces which are not machined subsequently, scale pits and surface dressing shall be permitted to a depth equal to one-third of the total value of the thickness tolerance.
In such cases, special tolerances shall be negotiated with the purchaser before the commencement of production. When tolerances for sheared ends are required, this will be indicated to the purchaser on the forging drawing before the commencement of production. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
Above 0,63 up to and including 1. Tolerances for fillet radii and edge radii are shown in Table 6 and examples of such radii are shown in Figure The permissible length of local deviation from the bar stock diameter or section adjoining a forged portion shall be up to 1,5 times the bar stock diameter or largest cross-sectional dimension, but with a maximum value of mm see Figure The tables showing dimensional tolerances are based on the R20 series of preferred numbers see ISO 3.
From Table 1 the tolerances see Figure 20 are found to be: The characteristics of the forging process require that, for any given forging, all tolerances for thickness dimensions are uniform. Up to and including 0,16;S3: Compliance with a British Standard does not of itself confer immunity from legal obligations.
The location 10243-11 burrs shall be indicated to the purchaser on the forging drawing for approval before the commencement of production. Pieces executees a chaud sur marteaux-pilons presses verticales. The minus tolerances do not apply to edge radii up to and including 3 mm when such radii are affected by subsequent removal of draft by trimming or punching.
The tolerances are determined from Table 3 and Table 4 in accordance with the greatest thickness dimension of the forging. Take the smart route to manage medical device compliance.
On forged surfaces which are to be machined subsequently, scale pits and surface dressing shall be permitted, but the maximum depth shall be such that at least one-half of the nominal enn allowance remains. The weight of the total length in question shall be calculated as if of unforged stock, irrespective of whether this is the case or not.
In such cases it can be arranged by negotiation between the purchaser and the supplier that the entire tolerance is shown as a positive one. In both cases, the permissible deviations shall be mentioned besides the relative measurements in the drawings of the forgings. Users are responsible for its correct application. Instances occur in which this tolerance is inadequate. By further movement to the right, the correct tolerance is found under the appropriate vertical column heading for the dimension concerned wherever possible the greatest dimension of length, width or height see 5.
ISO 3, Preferred numbers Series of preferred numbers. For undated references the latest edition of the publication referred to applies.
Centre-to-centre tolerances shall be applied independently of, and in addition to, any other tolerances. Examples are shown of circular and non-circular forgings see Figure 2 and Figure 3.